| 参数 | 价值 |
|---|---|
| 120 V DC | |
| 引领 | no |
| 宽度 | 54 mm |
| 编码 | A |
| 高度 | 42 mm |
| 长度 | 117 mm |
| 一般的 | When connecting the signal lines to the black PCB terminal blocks, please use a 0.4 x 2.0 mm screwdriver.The black PCB terminal blocks only require a minimal amount of operating force.Screwdriver: SZS 0,4X2,0 - 1205202Using larger screwdrivers or excessive force may damage the PCB terminal blocks.When using ferrules, the wires can be inserted straight into the PCB terminal blocks without opening the clamping area. |
| 应用 | Standard |
| 产品类型 | Distributor box |
| 组装说明 | NOTE:Observe the permissible bending radii when routing cables, since the degree of protection may be at risk if the bending forces are too high. Reduce mechanical loads upstream of the connector, e.g., by using cable ties. |
| 插槽数量 | 4 |
| 联系材料 | Cu alloy |
| 材料房屋 | PBT |
| 连接方式 | Spring-cage connection |
| 标称电压 UN | 120 V AC |
| 尺寸图 | |
| 申请须知 | Unused slots are to be sealed off prior to commissioning. Suitable sealing elements are to be found under "Accessories". |
| 职位数量 | 5 |
| 保护程度 | IP65 |
| 额定电流,总 | 12 A |
| 密封材料 O 形圈 | NBR |
| 标准名称 | M12 connector |
| 状态显示存在 | No |
| 电缆外径 | 7 mm ... 12 mm |
| 接触载体材料 | PA |
| 接触面材料 | gold-plated |
| 材质:螺纹套筒 | PBT |
| 标准/规范 | IEC 61076-2-101 |
| 模塑料 | PUR |
| 剥离长度 信号线 | 6 mm |
| 拧紧扭矩,连接螺母 | 2.5 Nm |
| 剥线长度 电源 | 10 mm |
| 鞘的剥离长度 | 50 mm (Master cable) |
| 拧紧扭矩,盖螺钉 | 1 Nm |
| 环境温度(运行) | -25 °C ... 80 °C |
| 传感器/执行器连接系统 | M12-SPEEDCON-socket |
| 每个插槽的电流承载能力 | 4 A |
| 根据 UL 94 标准评定的阻燃等级 | V0 |
| 每条路径的最大载流能力 | 2 A |
| 插槽/位置 = 电线颜色或连接方式 | 1 / 4 (A) = WH |
| 导体横截面柔性信号线 | 0.2 mm² ... 0.5 mm² |
| 拧紧扭矩槽传感器/执行器电缆 | 0.4 Nm |
| 导体横截面柔性电源 | 0.2 mm² ... 1.5 mm² |
| 连接横截面 AWG 柔性信号线 | 24 ... 20 |
| 连接横截面 AWG 柔性电源 | 24 ... 16 |
| 用于固定外壳的安装螺钉的拧紧扭矩 | 0.5 Nm |
技术规格和性能数据
安装和操作指南